• +1 866-861-6424
  • This email address is being protected from spambots. You need JavaScript enabled to view it.

DESCRIPTION

DYNA® ANTIQUA 4350 is a clear and transparent premium performance penetrating sealer specially formulated to protect, enhance the color of, and to provide a protective finish to tumbled marble, acid-washed marble, textured, rough, and dimensional and natural stone surfaces. It will protect the surface against stains, dust, dirt, water, acid rain, chemical attack, mildew, fungus, U.V. rays, salt, oils, tar and efflorescence. Surface dirt should be removed using standard maintenance procedures. It allows moisture vapor transmission.
ANTIQUA 4350 also protects from freeze/thaw damage such as spalling, cracking and bubbling rendered by the harshest climates. It serves to densify the surface of any stone and will not peel or yellow.

FEATURES & ADVANTAGES

- Provides Color Enhancement
- Matte finish, enhances and preserves the colors of the treated surface
- Penetrates deeply for better and more durable protection against stains
- Reduces damages due to freeze-thaw cycles
- Resists all weather elements (sun, rain, frost, heat, salt, etc.)

USES

1. For interior and exterior use.
2. For floors, walls, counter tops, and ceilings.
3. May also be used as a grout release agent.
4. Not to be used to guard against hydro-static pressure.
5. Not intended for polished stone surfaces. For polished stone surfaces use DYNA REPEL 4220, SUPER IMPREGNATOR 4210 or IMPREGNATOR 4110.

RECOMMENDED SURFACES

Can be applied on surfaces such as:
- Textured, Rough and Dimensional Natural Stones
- Acid-Washed Marble
- Tumbled Marble

LIMITATIONS

1. Do not apply before 10 days following the completion of the work.
2. Ensure that the surface to which it is to be applied to is thoroughly dry and that no residual moisture is present.
3. Slates, natural stone, and unglazed ceramic tiles will darken with the effect that the color will be enhanced. Ensure that you always test first in an incospicuous area to determine if this is what you desire.
4. Do not apply below 0°C (32°F) or above 40°C (104°F).
5. Do not apply over vitreous pavers.
6. Do not use as a floor finish or floor polish.
7. Do not use over polished marble or granite or any other polished natural stone surface.
8. Not to be used to guard against hydro-static pressure.

SECTIONS     -    

DIRECTIONS

A. SURFACE PREPARATION

Wash the surface that is to be treated and let dry completely before application. Wash with DYNA brand of cleaners. Ensure that the surface is completely dry and there is no residual moisture present.

B. APPLICATION

1. Apply ANTIQUA 4350 evenly over the surface using a clean dry brush, roller or spray on.
2. Apply evenly and do not allow the product to puddle on the surface.
3. Allow the sealer to penetrate the stone surface for about 1 to 2 hours.
4. With a clean dry cloth or terry cloth pick up and buff up the surface. Remove all excess sealer on the surface of the stone.
5. Let dry for at least 24 hours.
6. For maximum protection a repeat application is recommended.
7. If no grout release agent will be used for natural stone then the sealer must be applied at least once PRIOR to grouting.
8. ANTIQUA 4350 may be applied over a worn surface. First remove the old coat of ANTIQUA 4350 with a paint and varnish remover.
9. Depending on tile absorption, 2 to 4 coats may be required.
10. Allow at least 12 hour cure between coats.

PACKAGING

DYNA® ANTIQUA 4350 is available in:
- 500 mL (0.53 US quarts)
- 1 L (1.06 US quarts)
- 3.78 L (1 US gallon)
- 18.9 L (5 US gallons)

COVERAGE

7 m2 (75 ft2) to 23.2 m2 (250 ft2) per 1 L (1.06 US Quart) depending on the surface treated.


SAFETY WARNINGS

CAUTION
Contains petroleum distillates. If swallowed, give plenty of air and call physician immediately. This product is combustible. Keep away from heat, sparks, and open flames. Ensure work area is properly ventilated. Turn off all pilot lights or ignition sources that may ignite this product. Do not smoke in the vicinity of this product when it is being applied. Avoid contact with skin and eyes. If product contacts skin flush with plenty of water. If product comes in contact with eyes flush with plenty of water and consult a physician immediately.
KEEP OUT OF REACH OF CHILDREN

WARNING
Refer to SDS (Safety Data Sheets) for additional information.

NOTICE

DYNA shall not be liable for incidental and consequential damages, indirectly or directly sustained, nor for any loss by application of these goods not in accordance with the printed instructions or for other than the intended use. Before using the user shall determine the suitability of the product for its intended use and the user will assume all risks and liabilities that may arise in connection therewith. DYNA’s liability is expressly limited to the replacement of defective goods. Any claim shall be deemed waived unless the claim is made in writing to DYNA within 15 days
from the date it was, or reasonably should have been,
discovered that the product was defective.

LIMITED WARRANTY

This premium quality product was designed to satisfy the user. If you are not satisfied after Surface Testing on a small area, please contact our technical service department immediately.
NO WARRANTIES expressed or implied are offered by DYNA. The Manufacturer’s liability is limited to the replacement of products proven defective.
The user assumes all risks and liabilities associated with the use of this product.


DESCRIPTION

DYNA® GROUT GUARD 4100 is a premium performing Silane/Siloxane water-borne grout sealer and protector. It will protect from many items, which may stain your grout joints and also from acid rain, dirt, mildew, fungus, salt, efflorescence. It provides 100 % moisture vapour transmission, which is important for exterior tile work.
It will increase freeze / thaw resistance and protect from spalling, cracking and bubbling of your grout joints rendered by the harshest climates. It will not yellow and offers no surface appearance change to your grout joints. It will extend the life of your grout joints by many years.

USES

1. For interior and exterior use.
2. Can be used for floor, wall, counter top, and ceiling grout joints.

RECOMMENDED SURFACES

Can be applied on surfaces such as:
- Textured, Rough and Dimensional Natural Stones
- Acid-Washed Marble
- Tumbled Marble

LIMITATIONS

1. Not to be used to guard against hydrostatic pressure.
2. Do not apply before 10 days following the completion of the work.
3. Do not apply below 5°C ( 40°F ) or above 40°C ( 104°F ).
4. Not to be used for chemical grouting. Only effective on cementitious type of grouting.

SECTIONS     -    

DIRECTIONS

A. SURFACE PREPARATION

Ensure that the grout joints are clean and thoroughly dry prior to application. Use DYNA brand of cleaners to clean the grout joints.

B. APPLICATION

1. Apply GROUT GUARD 4100 evenly over the grout surface by spraying.
2. Wipe off excess material that sprayed on your tilework.
3. Allow the sealer to sit and absorb on the surface of the grout joints for 5 to 10 minutes.
4. Wipe up excess from the surface of the grout joints.
5. A repeat application is recommended.
6. Allow to cure for 24 to 48 hours.

CLEAN-UP

Clean hands and tools with clean water.

PACKAGING

DYNA® GROUT GUARD 4100 is available in:
- 500 mL (0.53 US quarts)

COVERAGE

18.6 m2 (200 ft2) to 55.7 m2 (600 ft2) per litre, depending on the absorbency, quality and the type of grout joints.


SAFETY WARNINGS

CAUTION
If swallowed call a physician immediately.
If splashed in eyes or skin rinse with plenty of water.
KEEP OUT OF REACH OF CHILDREN

WARNING
Refer to SDS (Safety Data Sheets) for additional information.

NOTICE

DYNA shall not be liable for incidental and consequential damages, indirectly or directly sustained, nor for any loss by application of these goods not in accordance with the printed instructions or for other than the intended use. Before using the user shall determine the suitability of the product for its intended use and the user will assume all risks and liabilities that may arise in connection therewith. DYNA’s liability is expressly limited to the replacement of defective goods. Any claim shall be deemed waived unless the claim is made in writing to DYNA within 15 days
from the date it was, or reasonably should have been,
discovered that the product was defective.

LIMITED WARRANTY

This premium quality product was designed to satisfy the user. If you are not satisfied after Surface Testing on a small area, please contact our technical service department immediately.
NO WARRANTIES expressed or implied are offered by DYNA. The Manufacturer’s liability is limited to the replacement of products proven defective.
The user assumes all risks and liabilities associated with the use of this product.


DESCRIPTION

DYNA® IMPREGNATOR 4110 is a clear and transparent high performance silicone penetrating sealant specially formulated to protect unglazed ceramic tiles, their joints, marble, granite, slate, terrazzo, sandstone, limestone, quartzite, quarry tile, paver tile, brick, clay roof tile, masonry surfaces, stucco and concrete against stains, dust, dirt, water, acid rain, chemical attack, mildew, fungus, UV rays, salt, oils and efflorescence damage. It is a sealant that allows moisture vapor transmission. IMPREGNATOR 4110 also protects from freeze / thaw damage such as spalling, cracking and bubbling rendered by the harshest climates.

FEATURES & ADVANTAGES

- Provides Invisible Protections
- Treated surfaces develop hydrophobic properties

USES

1. For interior and exterior use.
2. For floors, walls, counter tops, roofs and ceilings.
3. May also be used as a grout release agent.

RECOMMENDED SURFACES

Can be applied on surfaces such as:
- Unglazed Ceramic Tiles
- Cermaic Tile Joints
- Marble
- Granite
- Slate
- Terrazzo
- Sandstone
- Limestone
- Quartzite
- Quarry Tile
- Paver Tile
- Brick
- Clay Roof Tile
- Masonry Surfaces
- Stucco
- Conctrete

LIMITATIONS

1. Do not apply before 10 days following the completion of the work.
2. Certain types of slates and natural stone may darken slightly with the effect that the color will be enhanced, ensure that you always test first to determine if this is what you desire.
3. Do not apply below 0 °C ( 32 °F ) or above 40 °C ( 104 °F ).
4. Not to be used to provide oleophobic properties to surface to be treated. Use REPEL 4220 or SUPER IMPREGNATOR 4210 instead.
5. Not to be used to enhance the color of the surface to be treated. Use TerraSeal Matte 4300, TerraSeal Gloss 4320, TerraCotta 4330 or ANTIQUA 4350 instead.
6. Not to be used to guard against hydrostatic pressure.

SECTIONS     -    

DIRECTIONS

A. SURFACE PREPARATION

Wash the surface that is to be impregnated and let dry completely before application. Wash with a DYNA brand of cleaners.

B. APPLICATION (ON POLISHED SURFACES)

1. On polished surfaces apply IMPREGNATOR 4110 evenly over the surface using a clean dry cloth, brush , roller or spray on.
2. Let dry for at least 1/2 hour.
3. For maximum protection a repeat application is recommended.
4. Wipe off excess and buff up using a clean dry cloth.

C. APPLICATION (ON NON-POLISHED SURFACES)

1. For non-polished surfaces no buffing or wiping of excess material is required.
2. If no grout release agent will be used for unpolished natural stone then IMPREGNATOR 4110 must be applied at least once prior to grouting.
3. Avoid puddling of material in grout joints.

PACKAGING

DYNA® IMPREGNATOR 4110 is available in:
- 500 mL (0.53 US quarts)
- 1 L (1.06 US quarts)
- 3.78 L (1 US gallon)
- 18.9 L (5 US gallons)

COVERAGE

14 m2 (150 ft2) to 28 m2 (300 ft2) per 1 L (1.06 US Quart) depending on the surface treated


SAFETY WARNINGS

CAUTION
Contains petroleum distillates. If swallowed, give plenty of air and call physician immediately. This product is combustible. Keep away from heat, sparks, and open flames. Ensure work area is properly ventilated. Turn off all pilot lights or ignition sources that may ignite this product. Do not smoke in the vicinity of this product when it is being applied. Avoid contact with skin and eyes. If product contacts skin flush with plenty of water. If product comes in contact with eyes flush with plenty of water and consult a physician immediately.
KEEP OUT OF REACH OF CHILDREN

WARNING
Refer to SDS (Safety Data Sheets) for additional information.

NOTICE

DYNA shall not be liable for incidental and consequential damages, indirectly or directly sustained, nor for any loss by application of these goods not in accordance with the printed instructions or for other than the intended use. Before using the user shall determine the suitability of the product for its intended use and the user will assume all risks and liabilities that may arise in connection therewith. DYNA’s liability is expressly limited to the replacement of defective goods. Any claim shall be deemed waived unless the claim is made in writing to DYNA within 15 days
from the date it was, or reasonably should have been,
discovered that the product was defective.

LIMITED WARRANTY

This premium quality product was designed to satisfy the user. If you are not satisfied after Surface Testing on a small area, please contact our technical service department immediately.
NO WARRANTIES expressed or implied are offered by DYNA. The Manufacturer’s liability is limited to the replacement of products proven defective.
The user assumes all risks and liabilities associated with the use of this product.


DESCRIPTION

DYNA® REPEL 4220 is a clear and transparent premium performance penetrating impregnating agent specially formulated to protect porous natural and dimensional stone such as rough, splif-faced, textured, acid-washed, honed, flame finished and sandblasted marble, granite, slate, sandstone, limestone, and quartzite, against stains, dust, dirt, water, acid rain, chemical attack, mildew, fungus, U.V. rays, salt, oil, tar and damage from efflorescence. Surface dirt should be removed using standard maintenance procedures. It allows moisture vapor transmission.
REPEL 4220 also protects from freeze/thaw damage such as spalling, cracking and bubbling rendered  by the harshest climates. It serves to densify the surface of any stone and yet offers no appearance change. REPEL 4220 is not a sealer and as such leaves no surface film to peel or yellow. This product also serves as an anti-graffiti agent. Surfaces treated with this product have a higher co-efficient of friction, therefore polished stone surfaces such as floors become less slippery.

FEATURES & ADVANTAGES

- Provides Invisible Protections
- Treated surfaces develop hydrophobic properties
- Treated surfaces develop oleophobic properties

RECOMMENDED SURFACES

Can be applied on surfaces such as:
- Rough, split-faced, textured, acid-washed, honed, flame finished and sand blasted marble
- Granite
- Slate
- Sandstone
- Limestone
- Quartzite

USES

1. For interior and exterior use.
2. For floors, walls, counter tops, roofs, ceilings and furniture manufacture from natural stone.
3. May also be used as a grout release agent.

LIMITATIONS

1. Do not apply before 10 days following the completion of the work.
2. Certain types of slates and natural stone may darken slightly with the effect that the color will be enhanced, ensure that you always test first to determine if this is what you desire.
3. Do not apply below 0 °C ( 32 °F ) or above 40 °C ( 104 °F ).
4. Not to be used to provide oleophobic properties to surface to be treated. Use REPEL 4220 or SUPER IMPREGNATOR 4210 instead.
5. Not to be used to enhance the color of the surface to be treated. Use TerraSeal Matte 4300, TerraSeal Gloss 4320, TerraCotta 4330 or ANTIQUA 4350 instead.
6. Not to be used to guard against hydrostatic pressure.

SECTIONS     -    

DIRECTIONS

A. SURFACE PREPARATION

Wash the surface that is to be treated and let dry completely before application. Wash with DYNA brand of cleaners. Ensure that the surface is completely dry and there is no residual moisture present.

B. APPLICATION

1. Apply REPEL 4220 evenly over the surface using a clean dry cloth, brush , roller or spray on.
2. Permit the product to absorb into the surface for at least one half hour.
3. For polished surfaces wipe up the excess and buff up with a clean dry cloth after the product had a chance to absorb into the surface. Non-polished surfaces need not have the excess wiped up.
4. Let dry and do not permit heavy foot traffic for at least 24 hours.
5. For maximum protection a repeat application is recommended.
6. If no grout release agent will be used for natural stone then this product must be applied at least once PRIOR to grouting.

PACKAGING

DYNA® REPEL 4220 is available in:
- 500 mL (0.53 US quarts)
- 1 L (1.06 US quarts)
- 3.78 L (1 US gallon)
- 18.9 L (5 US gallons)

COVERAGE

23 m2 (250 ft2) to 41 m2 (450 ft2) per 1 L (1.06 US Quart) depending on the surface treated


SAFETY WARNINGS

CAUTION
Contains petroleum distillates. If swallowed, give plenty of air and call physician immediately. This product is combustible. Keep away from heat, sparks, and open flames. Ensure work area is properly ventilated. Turn off all pilot lights or ignition sources that may ignite this product. Do not smoke in the vicinity of this product when it is being applied. Avoid contact with skin and eyes. If product contacts skin flush with plenty of water. If product comes in contact with eyes flush with plenty of water and consult a physician immediately.
KEEP OUT OF REACH OF CHILDREN

WARNING
Refer to SDS (Safety Data Sheets) for additional information.

NOTICE

DYNA shall not be liable for incidental and consequential damages, indirectly or directly sustained, nor for any loss by application of these goods not in accordance with the printed instructions or for other than the intended use. Before using the user shall determine the suitability of the product for its intended use and the user will assume all risks and liabilities that may arise in connection therewith. DYNA’s liability is expressly limited to the replacement of defective goods. Any claim shall be deemed waived unless the claim is made in writing to DYNA within 15 days
from the date it was, or reasonably should have been,
discovered that the product was defective.

LIMITED WARRANTY

This premium quality product was designed to satisfy the user. If you are not satisfied after Surface Testing on a small area, please contact our technical service department immediately.
NO WARRANTIES expressed or implied are offered by DYNA. The Manufacturer’s liability is limited to the replacement of products proven defective.
The user assumes all risks and liabilities associated with the use of this product.


DESCRIPTION

DYNA® SUPER IMPREGNATOR 4210 is a clear and transparent high performance silicone penetrating sealant specially formulated to protect unglazed ceramic tiles, their joints, marble, granite, slate, terrazzo, sandstone, limestone, quartzite, quarry tile, paver tile, brick, clay roof tile, masonry surfaces, stucco and concrete against graffiti, stains, dust, dirt, water, acid rain, chemical attack, mildew, fungus, UV rays, salt, oils and efflorescence damage. Surface dirt should be removed using standard maintenance procedures. It allows moisture vapor transmission.
SUPER IMPREGNATOR 4210 also protects from freeze / thaw damage such as spalling, cracking and bubbling rendered by the harshest climates. It serves to densify the surface of any stone yet offers no appearance change. Since it is not a sealer, it will not yellow and leave no surface film.

FEATURES & ADVANTAGES

- Provides Invisible Protections
- Anti-Graffiti Agent
- Treated surfaces develop hydrophobic properties
- Treated surfaces develop oleophobic properties

USES

- For interior and exterior use
- For floors, walls, counter tops, roofs and ceilings
- May also be used as a grout release agent

RECOMMENDED SURFACES

Can be applied on vertical and horizontal surfaces such as:
- Unglazed Ceramic Tiles
- Ceramic Tile Joints
- Marble
- Granite
- Slate
- Terrazzo
- Sandstone
- Limestone
- Quartzite
- Quarry Tile
- Paver Tile
- Brick
- Clay Roof Tile
- Masonry Surfaces
- Stucco
- Concrete

LIMITATIONS

1. Do not apply before 10 days following the completion of the work.
2. Certain types of slates and natural stone may darken slightly with the effect that the color will be enhanced, ensure that you always test first to determine if this is what you desire.
3. Do not apply below 0°C (32°F) or above 40°C (104°F).
4. Not to be used to enhance the color of the surface to be treated. Use TerraSeal Matte 4300, TerraSeal Gloss 4320, TerraCotta 4330 or ANTIQUA 4350 instead.
6. Not to be used to guard against hydrostatic pressure.

SECTIONS     -    

DIRECTIONS

A. SURFACE PREPARATION

Wash the surface that is to be impregnated and let dry completely before application. Wash with a DYNA brand of cleaners.

B. APPLICATION

1. On polished surfaces apply SUPER IMPREGNATOR 4210 evenly over the surface using a clean dry cloth, brush, roller or spray on.
2. Let dry for at least 1/2 hour.
3. For maximum protection a repeat application is recommended. Wipe off excess and buff up using a clean dry cloth.
4. For non-polished surfaces no buffing or wiping of excess material is required.
5. If no grout release agent will be used for unpolished natural stone then IMPREGNATOR 4110 must be applied at least once prior to grouting.
6. Avoid puddling of material in grout joints.

PACKAGING

DYNA® SUPER IMPREGNATOR 4210 is available in:
- 500 mL (0.53 US quarts)
- 1 L (1.06 US quarts)
- 3.78 L (1 US gallon)
- 18.9 L (5 US gallons)

COVERAGE

14 m2 (150 ft2) to 28 m2 (300 ft2) per 1 L (1.06 US Quart) depending on the surface treated


SAFETY WARNINGS

CAUTION
Contains petroleum distillates. If swallowed, give plenty of air and call physician immediately. This product is combustible. Keep away from heat, sparks, and open flames. Ensure work area is properly ventilated. Turn off all pilot lights or ignition sources that may ignite this product. Do not smoke in the vicinity of this product when it is being applied. Avoid contact with skin and eyes. If product contacts skin flush with plenty of water. If product comes in contact with eyes flush with plenty of water and consult a physician immediately.
KEEP OUT OF REACH OF CHILDREN

WARNING
Refer to SDS (Safety Data Sheets) for additional information.

NOTICE

DYNA shall not be liable for incidental and consequential damages, indirectly or directly sustained, nor for any loss by application of these goods not in accordance with the printed instructions or for other than the intended use. Before using the user shall determine the suitability of the product for its intended use and the user will assume all risks and liabilities that may arise in connection therewith. DYNA’s liability is expressly limited to the replacement of defective goods. Any claim shall be deemed waived unless the claim is made in writing to DYNA within 15 days
from the date it was, or reasonably should have been,
discovered that the product was defective.

LIMITED WARRANTY

This premium quality product was designed to satisfy the user. If you are not satisfied after Surface Testing on a small area, please contact our technical service department immediately.
NO WARRANTIES expressed or implied are offered by DYNA. The Manufacturer’s liability is limited to the replacement of products proven defective.
The user assumes all risks and liabilities associated with the use of this product.


DESCRIPTION

DYNA® TERRASEAL GLOSS 4320 Sealer is a clear and transparent premium performance penetrating sealer specially formulated to protect, enhance the color of, and provide a protective gloss finish to textured, rough, split faced, honed, sandblasted, and flame finished dimensional and natural stone surfaces, and their joints. It can be used on natural and dimensional stone such as slate, sandstone, honed limestone, quartzite, granite, marble, serpentine, and onyx to enhance the color of, provide a gloss sheen, and protect the surface against stains, dust, dirt, water, acid rain, chemical attack, mildew, fungus, UV rays, salt, oils, tar and efflorescence. Surface dirt should be removed using standard maintenance procedures. It allows moisture vapor transmission.
TERRASEAL GLOSS 4320 also protects from freeze / thaw damage such as spalling, cracking and bubbling rendered by the harshest climates. It serves to densify the surface of any stone and will not peel or yellow. It can also be used on unglazed tiles, their joints, terra cotta tiles, Spanish tiles, Brazilian tiles, and terrazzo surfaces.

FEATURES & ADVANTAGES

- Provides Color Enhancement
- Gloss finish, enriches and preserves the colors of the treated surface
- Penetrates deeply for better and more durable protection against stains
- Reduces damages due to freeze-thaw cycles
- Resists all weather elements (sun, rain, frost, heat, salt, etc)

USES

- For interior and exterior use
- For floors, walls, counter tops, and ceilings
- May also be used as a grout release agent
- Not to be used to guard against hydrostatic pressure
- Not intended for polished stone surfaces. For polished stone surfaces use DYNA REPEL 4220, SUPER IMPREGNATOR 4210 or IMPREGNATOR 4110
- To obtain color enhancement along with gloss properties use TERRASEAL GLOSS 4320 or TERRACOTTA 4330 instead

RECOMMENDED SURFACES

Can be applied on Natural and Dimensional Stone such as:
- Slate
- Sandstone
- Hones Limestone
- Quartzite
- Granite
- Marble
- Serpentine
- Onyx

LIMITATIONS

1. Do not apply before 10 days following the completion of the work.
2. Ensure that the surface to which it is to be applied to is thoroughly dry and that no residual moisture is present.
3. Slates, natural stone, and unglazed ceramic tiles will darken with the effect that the color will be enhanced. Ensure that you always test first in an inconspicuous area to determine if this is what you desire.
4. Do not apply below 0°C (32°F) or above 40°C (104°F).
5. Do not apply over vitreous pavers.
6. Do not use as a floor finish or floor polish.
7. Do not use over polished marble or granite or any other polished natural stone surface.
8. Not to be used to guard against hydrostatic pressure.

SECTIONS     -    

DIRECTIONS

A. SURFACE PREPARATION

Wash the surface that is to be treated and let dry completely before application. Wash with DYNA brand of cleaners. Ensure that the surface is completely dry and there is no residual moisture present.

B. MIXING

Pour the contents of the can in a metal bucket or paint tray.

C. APPLICATION

1. Apply TERRASEAL GLOSS 4320 evenly over the surface using a clean dry brush, roller or spray on. Apply evenly and do not allow the product to puddle on the surface.
2. After about 10 to 20 minutes provide another application and let stand for 10 to 15 minutes.
3. With clean and dry lint free rags pick up any residual sealer on the surface of the stone.
4. Let dry for at least 24 hours.
5. If no grout release agent will be used for natural stone then the sealer must be applied at least once PRIOR to grouting.
6. TERRASEAL GLOSS 4320 may be applied over a worn surface. First remove the old coat of TERRASEAL GLOSS 4320 with a paint and varnish remover.
7. Depending on tile absorption, 2 to 4 coats may be required. Allow at least a 12 hour cure between coats.

PACKAGING

DYNA®TERRASEAL GLOSS 4320 is available in:
- 500 mL (0.53 US quarts)
- 1 L (1.06 US quarts)
- 3.78 L (1 US gallon)
- 18.9 L (5 US gallons)

COVERAGE

26 m2 (283 ft2) to 88 m2 (950 ft2) per 3.78 L (1 gallon) depending on the surface treated.


SAFETY WARNINGS

CAUTION
Contains petroleum distillates. If swallowed, give plenty of air and call physician immediately. This product is combustible. Keep away from heat, sparks, and open flames. Ensure work area is properly ventilated. Turn off all pilot lights or ignition sources that may ignite this product. Do not smoke in the vicinity of this product when it is being applied. Avoid contact with skin and eyes. If product contacts skin flush with plenty of water. If product comes in contact with eyes flush with plenty of water and consult a physician immediately.
KEEP OUT OF REACH OF CHILDREN

WARNING
Refer to SDS (Safety Data Sheets) for additional information.

NOTICE

DYNA shall not be liable for incidental and consequential damages, indirectly or directly sustained, nor for any loss by application of these goods not in accordance with the printed instructions or for other than the intended use. Before using the user shall determine the suitability of the product for its intended use and the user will assume all risks and liabilities that may arise in connection therewith. DYNA’s liability is expressly limited to the replacement of defective goods. Any claim shall be deemed waived unless the claim is made in writing to DYNA within 15 days
from the date it was, or reasonably should have been,
discovered that the product was defective.

LIMITED WARRANTY

This premium quality product was designed to satisfy the user. If you are not satisfied after Surface Testing on a small area, please contact our technical service department immediately.
NO WARRANTIES expressed or implied are offered by DYNA. The Manufacturer’s liability is limited to the replacement of products proven defective.
The user assumes all risks and liabilities associated with the use of this product.


DESCRIPTION

DYNA® TERRASEAL GLOSS 4320 Sealer (Color Enhancer) (Gloss Finish) is a clear and transparent premium performance penetrating sealer specially formulated to protect, enhance the color of, and provide a protective gloss finish to textured, rough, split faced, honed, sandblasted, and flame finished dimensional and natural stone surfaces, and their joints. It can be used on natural and dimensional stone such as slate, sandstone, honed limestone, quartzite, granite, marble, serpentine, and onyx to enhance the color of, provide a gloss sheen, and protect the surface against stains, dust, dirt, water, acid rain, chemical attack, mildew, fungus, UV rays, salt, oils, tar and efflorescence. Surface dirt should be removed using standard maintenance procedures. It allows moisture vapor transmission.
TERRASEAL GLOSS 4320 also protects from freeze / thaw damage such as spalling, cracking and bubbling rendered by the harshest climates. It serves to densify the surface of any stone and will not peel or yellow. It can also be used on unglazed tiles, their joints, terra cotta tiles, Spanish tiles, Brazilian tiles, and terrazzo surfaces.

FEATURES & ADVANTAGES

- Provides Color Enhancement
- Matte finish, enhances and preserves the colors of the treated surface
- Penetrates deeply for better and more durable protection against stains
- Reduces damages due to freeze-thaw cycles
- Resists all weather elements (sun, rain, frost, heat, salt, etc)

USES

- For interior and exterior use
- For floors, walls, counter tops, and ceilings
- May also be used as a grout release agent
- Not to be used to guard against hydrostatic pressure
- Not intended for polished stone surfaces. For polished stone surfaces use DYNA REPEL 4220, SUPER IMPREGNATOR 4210 or IMPREGNATOR 4110
- To obtain color enhancement along with gloss properties use TERRASEAL GLOSS 4320 or TERRACOTTA 4330 instead

RECOMMENDED SURFACES

Can be applied on Natural and Dimensional Stone such as:
- Slate
- Sandstone
- Hones Limestone
- Quartzite
- Granite
- Marble
- Serpentine
- Onyx

LIMITATIONS

1. Do not apply before 10 days following the completion of the work.
2. Ensure that the surface to which it is to be applied to is thoroughly dry and that no residual moisture is present.
3. Slates, natural stone, and unglazed ceramic tiles will darken with the effect that the color will be enhanced. Ensure that you always test first in an inconspicuous area to determine if this is what you desire.
4. Do not apply below 0°C (32°F) or above 40°C (104°F).
5. Do not apply over vitreous pavers.
6. Do not use as a floor finish or floor polish.
7. Do not use over polished marble or granite or any other polished natural stone surface.
8. Not to be used to guard against hydrostatic pressure.

SECTIONS     -    

DIRECTIONS

A. SURFACE PREPARATION

Wash the surface that is to be treated and let dry completely before application. Wash with DYNA brand of cleaners. Ensure that the surface is completely dry and there is no residual moisture present.

B. MIXING

Pour the contents of the can in a metal bucket or paint tray.

C. APPLICATION

1. Apply TERRASEAL MATTE 4300 evenly over the surface using a clean dry brush, roller or spray on. Apply evenly and do not allow the product to puddle on the surface.
2. After about 10 to 20 minutes provide another application and let stand for 10 to 15 minutes.
3. With clean and dry lint free rags pick up any residual sealer on the surface of the stone.
4. Let dry for at least 24 hours.
5. If no grout release agent will be used for natural stone then the sealer must be applied at least once PRIOR to grouting.
6. TERRASEAL MATTE 4300  may be applied over a worn surface. First remove the old coat of TERRASEAL MATTE 4300 with a paint and varnish remover.
7. Depending on tile absorption, 2 to 4 coats may be required. Allow at least a 12 hour cure between coats.

PACKAGING

DYNA®TERRASEAL MATTE 4300 is available in:
- 500 mL (0.53 US quarts)
- 1 L (1.06 US quarts)
- 3.78 L (1 US gallon)
- 18.9 L (5 US gallons)

COVERAGE

26 m2 (283 ft2) to 88 m2 (950 ft2) per 3.78 L (1 gallon) depending on the surface treated.


SAFETY WARNINGS

CAUTION
Contains petroleum distillates. If swallowed, give plenty of air and call physician immediately. This product is combustible. Keep away from heat, sparks, and open flames. Ensure work area is properly ventilated. Turn off all pilot lights or ignition sources that may ignite this product. Do not smoke in the vicinity of this product when it is being applied. Avoid contact with skin and eyes. If product contacts skin flush with plenty of water. If product comes in contact with eyes flush with plenty of water and consult a physician immediately.
KEEP OUT OF REACH OF CHILDREN

WARNING
Refer to SDS (Safety Data Sheets) for additional information.

NOTICE

DYNA shall not be liable for incidental and consequential damages, indirectly or directly sustained, nor for any loss by application of these goods not in accordance with the printed instructions or for other than the intended use. Before using the user shall determine the suitability of the product for its intended use and the user will assume all risks and liabilities that may arise in connection therewith. DYNA’s liability is expressly limited to the replacement of defective goods. Any claim shall be deemed waived unless the claim is made in writing to DYNA within 15 days
from the date it was, or reasonably should have been,
discovered that the product was defective.

LIMITED WARRANTY

This premium quality product was designed to satisfy the user. If you are not satisfied after Surface Testing on a small area, please contact our technical service department immediately.
NO WARRANTIES expressed or implied are offered by DYNA. The Manufacturer’s liability is limited to the replacement of products proven defective.
The user assumes all risks and liabilities associated with the use of this product.


Go to top
JSN Ferado 2 is designed by JoomlaShine.com | powered by JSN Sun Framework