• +1 866-861-6424
  • This email address is being protected from spambots. You need JavaScript enabled to view it.

DESCRIPTION

DYNA® CERACID 8210 is a premium performing efflorescence and grout film remover for residential, commercial, and industrial ceramic tile, clay tile, and porcelain tile installations. This product is formulated to remove grout film and efflorescence remaining after new installations. It can also be used on old installations to remove efflorescence emerging from soluble calcium salts appearing on the surface.

USES

- For interior and exterior use.
- For floors, walls, masonry, and brick veneer cladding.

LIMITATIONS

1. Test CERACID 8210 in an inconspicuous area to determine if it is suitable for use.
2. Some grout joints may darken with the use of the product because of the metal oxides present.
3. Do not apply below 0°C (32°F) or above 40°C (104°F).
4. Do not allow the product to freeze.

SECTIONS     -    930000

DIRECTIONS

A. APPLICATION

1. For grout film removal, mix approximately 89 to 177 ml (3 to 6 fluid ounces) in a bucket with 3.78 L (1 gallon) of warm clean water.
2. With a mop, brush or sponge apply the solution onto the surface. Allow the solution to remain on the surface for 10 to 20 minutes and scrub the surface with a brush if possible.
3. Rinse the surface with cold clean water.
4. Ensure no residual solution remains on the surface.

NOTE: For efflorescence removal follow the same procedures, however, mix 177 to 295 ml (6 to 10 fluid ounces) in a bucket with 3.78 L (1 gallon) of warm clean water. Depending upon the degree to which grout film and efflorescence is present a repeat application may be required.

PACKAGING

DYNA® CERACID 8210 is available in:
- 946 ml (1.0 US quarts)


SAFETY WARNINGS

CAUTION
Avoid direct contact with skin. If in contact with skin rinse with clean water. Avoid contact with eyes. If in contact with eyes rinse thoroughly for 15 minutes with clean water. If swallowed drink plenty of water and seek medical attention immediately. This product is acidic in nature, therefore, do not mix with any other cleaner or allow the product to come in contact with metals.
KEEP OUT OF REACH OF CHILDREN

WARNING
Refer to SDS (Safety Data Sheets) for additional information.

NOTICE

DYNA shall not be liable for incidental and consequential damages, indirectly or directly sustained, nor for any loss by application of these goods not in accordance with the printed instructions or for other than the intended use. Before using the user shall determine the suitability of the product for its intended use and the user will assume all risks and liabilities that may arise in connection therewith. DYNA’s liability is expressly limited to the replacement of defective goods. Any claim shall be deemed waived unless the claim is made in writing to DYNA within 15 days
from the date it was, or reasonably should have been,
discovered that the product was defective.

LIMITED WARRANTY

This premium quality product was designed to satisfy the user. If you are not satisfied after Surface Testing on a small area, please contact our technical service department immediately.
NO WARRANTIES expressed or implied are offered by DYNA. The Manufacturer’s liability is limited to the replacement of products proven defective.
The user assumes all risks and liabilities associated with the use of this product.


DESCRIPTION

DYNA® CERACLENS 8200 is a premium performing concentrated intensive cleaner and detergent for residential, commercial, and industrial ceramic and porcelain tile surfaces. This product is formulated to dissolve heavy stains, greases, oils, waxes and grimy build-up commonly found on floors, walls, countertops, etc. This easy to use cleaner cleans, beautifies, and restores glazed and unglazed ceramic tile and porcelain tile surfaces, clay bricks, pavers and various cementitious surfaces.

USES

- For interior and exterior use.
- For ceramic porcelain, cementitious surfaces and many other surfaces.

LIMITATIONS

1. Test CERACLENS 8200 on a spare tile, grout joint or the surface to be cleaned in an inconspicuous area.
2. Do not apply below 0°C (32°F) or above 40°C (104°F).
3. Do not allow the product to freeze.
4. This product is designed for periodic intense cleaning, stripping waxes or stripping water-borne sealers only.

NOTE: For frequent or daily use, use CERASHINE 8220. This product is for use for medium to large surface areas. For localized cleaning use SPRAY & WIPE 8030.

SECTIONS     -    930000

DIRECTIONS

A. APPLICATION

1. For periodic intense cleaning, mix approximately 1 to 3 fluid ounces in a bucket with 1 gallon of warm clean water.
2. With a mop or sponge apply the solution in a swirling motion.
3. Do not apply heavy pressure as debris may scratch polished or glazed tile surfaces.
4. Mop up excess and let dry.
5. If solutions greater than this are used, a rinse with cold clean water may be required.
6. For an intense cleaning after a new tile or stone surface has been installed use 3 to 6 ounces instead and rinse afterwards.

NOTE: Do not apply heavy pressure as loose grout debris may scratch the polished or glazed tile surface.

PACKAGING

DYNA® CERACLENS 8200 is available in:
- 946 ml (1.0 US quarts)


SAFETY WARNINGS

CAUTION
Avoid direct contact with skin. If in contact with skin rinse with clean water. Avoid contact with eyes. If in contact with eyes rinse thoroughly for 15 minutes with clean water. If swallowed drink plenty of water and seek medical attention immediately. This product is acidic in nature, therefore, do not mix with any other cleaner or allow the product to come in contact with metals.
KEEP OUT OF REACH OF CHILDREN

WARNING
Refer to SDS (Safety Data Sheets) for additional information.

NOTICE

DYNA shall not be liable for incidental and consequential damages, indirectly or directly sustained, nor for any loss by application of these goods not in accordance with the printed instructions or for other than the intended use. Before using the user shall determine the suitability of the product for its intended use and the user will assume all risks and liabilities that may arise in connection therewith. DYNA’s liability is expressly limited to the replacement of defective goods. Any claim shall be deemed waived unless the claim is made in writing to DYNA within 15 days
from the date it was, or reasonably should have been,
discovered that the product was defective.

LIMITED WARRANTY

This premium quality product was designed to satisfy the user. If you are not satisfied after Surface Testing on a small area, please contact our technical service department immediately.
NO WARRANTIES expressed or implied are offered by DYNA. The Manufacturer’s liability is limited to the replacement of products proven defective.
The user assumes all risks and liabilities associated with the use of this product.


DESCRIPTION

DYNA® CERASHINE 8220 is a high performing concentrated neutral cleaner and detergent for residential, commercial, and industrial stone and tile surfaces. This product is formulated to dissolve stains, light greases, oils, and grimy build-up commonly found on floors, walls and countertops. This product is neutral in pH and is formulated for daily or frequent use and will not therefore remove waxes and sealers commonly used on floors.
This easy to use cleaner cleans, beautifies, and restores marble, granite, limestone, glazed and unglazed ceramic tile surfaces, clay bricks, pavers and various cementitious surfaces. It leaves no dulling film and provides a wet look. Special additives are present which prevent natural or dimensional stone surfaces from drying out. These additives also provide an added benefit of anti-soiling properties.

USES

- For interior and exterior use.
- For natural and dimensional stone, ceramic, porcelain, cementitious surfaces and many other surfaces.

LIMITATIONS

1. Test CERASHINE 8220 on a spare tile, grout joint or the surface to be cleaned in an inconspicuous area.
2. Do not apply below 0°C (32°F) or above 40°C (104°F).
3. Do not allow the product to freeze.
4. This product is designed for periodic intense cleaning, stripping waxes or stripping water-borne sealers only.

NOTE: For periodic intense cleaning, stripping waxes or sealers use CERACLENS 8200. This product is for use for medium to large surface areas. For localized cleaning use SPRAY & WIPE 8030.

SECTIONS     -    930000

DIRECTIONS

A. APPLICATION

1. For regular cleaning, mix approximately 1 to 3 fluid ounces in a bucket with 1 gallon of warm clean water.
2. With a mop or sponge apply the solution in a swirling motion.

NOTE: Do not apply heavy pressure as debris may scratch polished or glazed tile surfaces.

PACKAGING

DYNA® CERASHINE 8220 is available in:
- 946 ml (1.0 US quarts)


SAFETY WARNINGS

CAUTION
Avoid direct contact with skin. If in contact with skin rinse with clean water. Avoid contact with eyes. If in contact with eyes rinse thoroughly for 15 minutes with clean water. If swallowed drink plenty of water and seek medical attention immediately. This product is acidic in nature, therefore, do not mix with any other cleaner or allow the product to come in contact with metals.
KEEP OUT OF REACH OF CHILDREN

WARNING
Refer to SDS (Safety Data Sheets) for additional information.

NOTICE

DYNA shall not be liable for incidental and consequential damages, indirectly or directly sustained, nor for any loss by application of these goods not in accordance with the printed instructions or for other than the intended use. Before using the user shall determine the suitability of the product for its intended use and the user will assume all risks and liabilities that may arise in connection therewith. DYNA’s liability is expressly limited to the replacement of defective goods. Any claim shall be deemed waived unless the claim is made in writing to DYNA within 15 days
from the date it was, or reasonably should have been,
discovered that the product was defective.

LIMITED WARRANTY

This premium quality product was designed to satisfy the user. If you are not satisfied after Surface Testing on a small area, please contact our technical service department immediately.
NO WARRANTIES expressed or implied are offered by DYNA. The Manufacturer’s liability is limited to the replacement of products proven defective.
The user assumes all risks and liabilities associated with the use of this product.


DESCRIPTION

DYNA® MARBLE MAID 8000 is a high performing concentrated intensive cleaner and detergent for residential, commercial, and industrial stone and tile surfaces. This product is formulated to dissolve heavy stains, greases, oils, waxes, and grimy build-up commonly found on floors, walls and countertops. This easy to use cleaner cleans, beautifies, and restores marble, granite, limestone, all dimensional and natural stone surfaces, glazed and unglazed ceramic tile surfaces, clay bricks, pavers and various cementitious surfaces.

USES

- For interior and exterior use
- For natural and dimensional stone, ceramic, porcelain, cementitious and many other surfaces.

LIMITATIONS

1. Test MARBLE MAID 8000 on a spare tile, grout joint or the surface to be cleaned in an inconspicuous area.
2. Do not apply below 0°C (32°F) or above 40°C (104°F).
3. This product is designed for periodic intense cleaning, stripping waxes or stripping water-borne sellers only. For frequent or daily use, use STONE SOAP 8010. This is for use for medium to large surfaces areas. For localized cleaning use SPRAY & WIPE 8030.

SECTIONS     -    930000

DIRECTIONS

A. APPLICATION

1. For periodic intense cleaning, mix approximately 1 to 3 fluid ounces in a bucket with a gallon of warm clean water.
2. With a mop or sponge apply the solution in a swirling motion. Do not apply heavy pressure as debris may scratch polished stone surfaces.
3. Mock up excess and let dry.
4. If solutions greater than this are used, a rinse with cold clean water may be required.
5. For an intense cleaning after a new tile or stone has been installed use 3 to 6 ounces instead and rinse afterwards. Do not apply heavy pressure as loose grout debris may scratch the polished stone surface.

PACKAGING

DYNA® MARBLE MAID 8000 is available in:
- 946 ml (1.0 US quarts)


SAFETY WARNINGS

CAUTION
Avoid direct contact with skin. If in contact with skin rinse with clean water. Avoid contact with eyes. If in contact with eyes rinse thoroughly for 15 minutes with clean water. If swallowed drink plenty of water and seek medical attention immediately.
KEEP OUT OF REACH OF CHILDREN

WARNING
Refer to SDS (Safety Data Sheets) for additional information.

NOTICE

DYNA shall not be liable for incidental and consequential damages, indirectly or directly sustained, nor for any loss by application of these goods not in accordance with the printed instructions or for other than the intended use. Before using the user shall determine the suitability of the product for its intended use and the user will assume all risks and liabilities that may arise in connection therewith. DYNA’s liability is expressly limited to the replacement of defective goods. Any claim shall be deemed waived unless the claim is made in writing to DYNA within 15 days
from the date it was, or reasonably should have been,
discovered that the product was defective.

LIMITED WARRANTY

This premium quality product was designed to satisfy the user. If you are not satisfied after Surface Testing on a small area, please contact our technical service department immediately.
NO WARRANTIES expressed or implied are offered by DYNA. The Manufacturer’s liability is limited to the replacement of products proven defective.
The user assumes all risks and liabilities associated with the use of this product.


DESCRIPTION

DYNA® STONE SOAP 8010 is a high performing concentrated neutral cleaner and detergent for residential, commercial, and industrial stone and tile surfaces. This product is formulated to dissolve stains, light greases, oils, and grimy build-up commonly found on floors, walls, countertops, etc. This product is neutral in pH and is formulated for daily or frequent use and will not therefore remove waxes and sealers commonly used on floors.
This easy to use cleaner cleans, beautifies, and restores marble, granite, limestone, glazed and unglazed ceramic tile surfaces, clay, bricks, pavers and various cementitious surfaces. It leaves no dulling film and provides a wet look. Special additives are present which prevent natural or dimensional stone surfaces from drying out. These additives also provide an added benefit of anti-soiling properties.

USES

- For interior and exterior use.
- For natural and dimensional stone, ceramic, porcelain, cementitious and many other surfaces.

LIMITATIONS

1. Test STONE SOAP 8010 on a spare tile, grout joint or the surface to be cleaned in an inconspicuous area.
2. Do not apply below 0°C (32°F) or above 40°C (104°F).
3. Do not allow the product to freeze.

NOTE: For periodic intense cleaning or stripping waxes use DYNA's MARBLE MAID 8000.

SECTIONS     -    930000

DIRECTIONS

A. APPLICATION

1. For regular cleaning, mix approximately 1 to 3 fluid ounces with 1 gallon of warm clean water.
2. Apply the solution with a mop or a sponge to desired surface. Do not apply heavy pressure as debris may scratch polished stone surfaces.
3. Mop up excess and let dry.
4. No rinsing required.

PACKAGING

DYNA® STONE SOAP 8010 is available in:
- 946 ml (1.0 US quarts)


SAFETY WARNINGS

CAUTION
Avoid direct contact with skin. If in contact with skin rinse with clean water. Avoid contact with eyes. If in contact with eyes rinse thoroughly for 15 minutes with clean water. If swallowed drink plenty of water and seek medical attention immediately.
KEEP OUT OF REACH OF CHILDREN

WARNING
Refer to SDS (Safety Data Sheets) for additional information.

NOTICE

DYNA shall not be liable for incidental and consequential damages, indirectly or directly sustained, nor for any loss by application of these goods not in accordance with the printed instructions or for other than the intended use. Before using the user shall determine the suitability of the product for its intended use and the user will assume all risks and liabilities that may arise in connection therewith. DYNA’s liability is expressly limited to the replacement of defective goods. Any claim shall be deemed waived unless the claim is made in writing to DYNA within 15 days
from the date it was, or reasonably should have been,
discovered that the product was defective.

LIMITED WARRANTY

This premium quality product was designed to satisfy the user. If you are not satisfied after Surface Testing on a small area, please contact our technical service department immediately.
NO WARRANTIES expressed or implied are offered by DYNA. The Manufacturer’s liability is limited to the replacement of products proven defective.
The user assumes all risks and liabilities associated with the use of this product.


Go to top
JSN Ferado 2 is designed by JoomlaShine.com | powered by JSN Sun Framework